MVP Racing Engines 
BACK to BACK Championship Engines 2005 & 2006
Winner Again in 2008

Winner of the

 NQS Engine Builder Cup of the year Award for 2005, 2006 & 2008

   

Forged Steel Crankshafts.  available in 3.250", 3.750"                        $399.00
 Billet Aluminum Connecting Rod by Super Cub.  available in 5,300, 5.750, 5.812, 5.875, 5.906 5.937, 5.968, 6.000, 6.031", 6.125, 6.187, 6.250.  $140.00 10 HP rod.  Same as the other rods offered by Super Cub, but is made for a 10hp wrist pin and stock length            $140.00
Steel Oil Pans available in 1 quart $125.00  Copper Head Gaskets for 10,12, 14 and 16hp.  available in 0.031"  $14: 0.062" $20. Engine Bearing Plate.  $125.00
 
Aluminum Front Engine Pulley  $75.00.  Please specify crank shaft size. Chevy Points Bracket for Kohler.  Bolts on in place of stock points.  $16.80
Points Cover for Bracket (Red, Black or Yellow)  $6.30		 Accel Chevy heavy spring points with Accel Condensor  $29.00.  
No Picture Available
Rod Bearing w/ bearing lock hole drilled for MSC Rod             $16.00 Stock Altered Block 16 hp design                   $725.00 Stock Altered Block and Crank Combo         $900.00
Mandrel Bent Chrome Exhaust Pipe 1 3/8, 1 5/8 and 1 3/4 ID available
             All Sizes One Price $50.00  Plain Mandrel Bent Pipes   $20.00		 Exhaust Flange for use with Mandrel Bent pipes. 4 bolt flange for J2, Jones and Woolam for 1 3/4 pipe       $30.00 Steel Cam Gear, fits MSC, Vogel, Lakota and Nichols steel camshafts.              $50.00
Spark Plug Index Washers.  2 (two) .020, 2 (two) .031, 6 (six) .062 washers.   10 pack for $3.00 1 cyl Kohler Head Hold Down.  A must for hi-pro engines.  $45.00 Workbench Engine/Transmission Holder stand.  $125.00
Blank Head Billet Aluminum for 16hp Kohler              $45.00      Blank Heads for 10-14hp Kohler, with 9 head bolts      $45.00 Chrome Tappet Cover Plate and hardware.  Factory Kohler cover chrome plated to "dress up" you engine $25.00 Front Points Plate, cam pins, ball bearings, needle bearing & attaching hardware.  $75.00
Billet Aluminum Connecting Rod.  6.145" long with .669" wrist pin hole for use with 3.270" or 3.300" piston for 10hp engine  $140.00 Dual valve springs, aluminum retainers and hardened valve keepers.  Use only the outer spring for cast cams and both inner and outer for steel cams.  Reverse Wound Springs.  Per Set     $28.00 4340 Billet Super Duty Cranks
2.875" (10hp), 3.050", 3.25", 3.500", 3.680", 3.750", 3.875", 3.937", 4.00" $500.00 
12hp Exhaust flange with mounting bolts for 1 3/8" pipe.           $30.00 16hp Exhaust flange with mounting bolts for 1 5/8" pipe. $35.00 12 ball main bearings.  Better than the 11 ball bearings.  USA Made Top Quality.   $52.00 ea.

Exhaust Pipe Covers Various Colors fits 1 3/8", 1 5/8" and 1 3/4" exhaust pipes listed above.              $8.00 MVP RACING ENGINES. Pro Stock 50.5 cu in.  4.125 x 3.750.  CNC Ported $4,295.00.  NQS Version Pro/Super $5,400 K&N Air Filter;  Fits our bolt on V-Stack. 7"OD x 6"Long. Comes with clamp  $48.95
Copper Side Cover Gasket: Replaces stock thick Kohler gasket.  Reusable, 0.031" thick.   $10.00 Replacement Starter Ring Gear.                     $95.00 Steel Camshaft Blank.  Fits MSC, Lakota and Nichols style pins.                           $65.00
Stainless Steel Valves. 2.100, 1.625, 1.380  $45.00 each Large Head Valve Adjusters for Kohler.  For offset guides. $8.00 Super Large Base Lifters for cams over .570" lift     $45.00
Lightened Steel Flywheel weighs 10 Lbs.  Made to fit starter ring gear.   $240.00  Titanium Valves for Kohler 1 cylinder 2.035", 1.625", 1.380" -- Command Stock size, Over size 5/16" stems and for Pro Altered $95.00 each Offset Bronze Valve Guides for Kohler Engines.  Offset is .085" from center.    $20.00 each
 Head Stud Kit for Kohler Engines.  Includes 10 (ten) B7 Studs, Extra Thick Washers, Grade 8 nuts.  $25.00 JE Lightweight Custom Pistons/includes Rings and Pins.
3.405, 3.420, 3,530, 3,775, 3.937, 4.060, 4.125          $172.00		 Economy Exhaust Flanges for 10-14hp and 16hp Kohler.  Bolts on engine, exhaust pipe can be welded onto flange.    $10.00
 
  Billet Aluminum Cam Cover For 1 Cylinder Kohler  $52.00 1 Cylinder Kohler Magnum Steel Flywheel for ring gear   $190.00
Does not include magnet, use one off of stock flywheel
  KNC:  K&N Filter Cover (similar to our dust covers for carb and exhaust)  $15.00
 F-19: 10-16hp Kohler For Ring Gear 19lbs  $157.50 F-25: 10-16hp Kohler For Ring Gear 25lbs  $178.50  F-20: 10-16hp Kohler 20 lbs 
$141.75


 
WOOLAM BLOCKS These blocks are available, we have the 50.5 tops in stock and the 30 cubic inch tops soon.  Price is $1,200.00 for the complete block.  The aluminum block bottoms are $800.00 and the ductile iron block tops are $400.00. CenPeCo Gard-N-Go Oil  This oil is specially blended for the air-cooled single cylinder engines and also is an excellent oil for V-twin engines.. This oil will help protect the lifters and camshaft in the V-twin engines.  Available in 20wt or 30wt.  In stock  Priced at $5.60 per quart.
 Port Support Plate for 1cyl Kohler Engines.  
This is a 1/4" thick aluminum plate that bolts on the side of the Kohler engine to support the port on large port/large valve engines.  Priced at $40.00 
   
Crank Trigger Ignition for Single Cylinder Engines.  Kit includes magnet ring, bracket and module.  Easy hook up. Buyer can use any 3 ohm coil, doesn't need a condenser to run.  Buyer must specify diameter of PTO end of crank at the block. MWSC steel crank requires a 1.5" magnet ring.  Also must specify bolt circle on front of the block for the module bracket to bolt on (5" or 5 5/8").  This crank trigger ignition set up will also allow you to use our Equus Tachometer on your 1 cylinder.  This ignition module has been tested on our 1cylinder engines for the past few years.  Part Number is "EI". Priced at $90.00.