Kohler Command Parts

Roller Cam Kit for Kohler Command  This kit includes billet steel cam blank with steel camshaft gear which features the large 5 bolt pattern and four roller lifters with tie bars.  This larger bolt circle on the cam will not slip like the smaller 4 bolt set up.   .505" lift 277-283 duration with 1.6 rocker arm ratio.  We've built several engines with this cam.  Good wide power band with very good torque numbers.  Complete kit priced at $620.00 Steel Cam Gear for Command $75.00 Steel Cam blank for Command $115.00
MSC Pro Altered Cast Cylinder Heads.  Bare heads have stock size valve seats installed and hard bronze valve guides for either 7mm or 5/16 stems.  Requires stock length 1 cyl. Kohler valves. 
Bare Head  $500.00 pair
Complete Heads $1,500 pair		 Stainless Steel Command Valves
Stock head size .300" longer stems $35.00 each
Titanium Command Valves. 
Stock Size or Custom available $95.00 each		 Double Valve Springs for .300 Longer Valves.  125# seat pressure 260# open (.600").    Set of four springs, four retainers with locators.  Uses stock keepers.  $64.00/set of 4
Single Valve Springs for Stock Valves with Retainers $48.00/set of 4
 
JE Kohler Command pistons w/rings and pins and clips.
3.051, 3.071, 3.270, 3.300, 3.375 3.583      $140.00 to $160.00 each depending on size.

 Command Throttle Bracket for Gas Pedal  Stainless steel (304) bracket to bolt onto the back of the stock Kohler Command downdraft carburetor to easily connect your gas pedal cable.  Bracket bolts onto where the fuel shut off solenoid bolted on at carburetor.  Priced at $6.00

 Lash caps for V-twin Cylinder engines  Lash caps saves the valve tip from wear by the roller rockers and prevents soft valves from being mushrooms.  Made from hardened 4140 steel and protective black oxide finish.  Designed for 7mm valves.  Priced at $4.00 each ($16.00 for set of 4)
Command Billet Rods with bearing lock.
Standard Length $110.00 each
+.150" longer Rods $110.00 each		 Kohler Command Cam Degree Tool  Patent Pending on this easy to use tool to degree your camshaft in on your Command V-Twin.  Also can check the end play on the cam and crankshaft with this tool.  Made of high strength grade 1/2" aluminum.  $30.00 each
Velocity Stack for Stock Kohler Command Carbs. Increase flow and Horsepower.  Accepts KN Filter.
                                   $52.50 each
Kohler Command Intake Gaskets for stock heads      $3.00/pair Kohler Command Weldable Exhaust Flanges   $11.00/pair Spark Plug Index Washers.  2 (two) .020, 2 (two) .031, 6 (six) .062 washers.   10 pack for $3.00
Steel Intake Flanges for Command Stock Heads     $11.00/pair Push Rod Guide Plates for stock Command heads.  A must for High RPM applications.  Made for stock diameter pushrods.   $15.00/pair Kohler Command Engine sleeves $60.00/pair
Used to sleeve your 18hp to 23hp engine up to the 3.270" 25hp bore or the 3.300" 27hp bore.  Machine your block, install, bore and hone $250.00.  All work done in our CNC machining center
Billet Steel Cranks for Command
Stock Stroke                     $650.00
Stroker Crank                   $675.00		 Kohler Command .031 Copper Head Gaskets  
18hp to 22hp
25hp
27hp
3.375 bore
3.583 bore          $18.00/pr.		 Command Steel Adjustable Flywheel for Ring Gear and Ignition.                     $275.00
V-Twin Command Intake Manifold Setup for MSC Plenum $150.00
MSC Plenum adapt 1.2 Carb to Intake $90.00
 		  V-Twin Command 2 into 1 header included copper gaskets $91.00 Billet Aluminum High Strength Magnet for Kohler Command. For hotter spark, better performance and won't come apart at high RPM like stock die-cast aluminum magnet will.  $60.00
 
 Kohler Command Aluminum Valve Covers comes with o-ring seal and stainless steel bolts $65.00/pair
   Kohler Command Aluminum Roller Rocker Kit Includes four 1.6 ratio roller rocker, four screw-in studs, four adjuster nuts, two aluminum inserts for head (requires some machining on head and use of .300" longer valves)
Use with billet valve covers listed to left or use a 1.0" valve cover spacers $136.00 for complete set. Now includes lash caps        
 Command Zoomie Header $45.00 per pair
Choice of size 1 1/8", 1 1/4" and 1 3/8".
 

MVP V-Twin Command Engine Packages:
$3,500.00 (18 - 25HP, 1.2 carb gas or alky, balanced stock crank, billet rods, flat top pistons, roller cam,
roller rockers, double springs, fully ported stock heads, valve cover spacers, steel adjustable flywheel, custom intake and header. 
Dyno-tuned.  Our most affordable price.  Power ranges from 50HP to 70HP.  GOOD CORE REQUIRED


$4,200.00 (18 to 25HP, same as above engine but with Pro Altered heads, camshaft and rocker up
grade, steel billet crankshaft) Options at extra cost  3" stroke crank, 3.375" big bore,
 cubic inch size up to 54 cubic inches.  Gas or Alky. 55HP to 85HP.  GOOD CORE REQUIRED

 
Command Zoomie Pipe Kit, Do It Yourself Kit  (includes two pipes & two flanges). Choice of 1 1/8", 1 1/4" & 1 3/8". 
 
$30.00 for Kit 
 		 Command Pipes, choice of sizes 1 1/8", 1 1/4" & 1 3/8". Pipes are 24" long.   $20.00 per pair
2  into 1 equal length side exit header.  Made to clear the hood of the 582 Cub Cadet style tractors.  Available in 1 1/8" and 1 3/8" primary tube size. Please Specify Stock Heads or Pro Altered Heads. included copper gaskets    $156.00
 Stock Kohler Command 2-barrel carb and intake for the CH series engines (horizontal crank).  We've dyno'd this set-up and its a
drop on installation, picked up 8 horsepower over our competitor's reworked 25 hp carb.  Carb is $254.00, intake is $92.00.  The package deal with gaskets is $346.00.  Perfect for the stock and stock altered class where OEM parts are required.

New Aluminum Flywheel for Kohler Command, weighs 1/2 the weight of the steel flywheel  $325.00

 
Velocity Stack for Kohler Command 2 Barrel Carb  $65.00 K&N Air Filter fits our velocity stack for 2 Barrel carb for Kohler Command  $65.00 Plenum to adapt 2-barrel manifold to vertical carb or Kohler 1-Cylinder Carb.  $95.00
Copper Exhaust Flange Gaskets for Kohler Command $6.00 per pair. Carb adaptor for downdraft Command carb to the Command vertical intake manifold.  The vertical intake flows nearly twice the air as the horizontal intake.  $45.00 Spring Locators for the Double Valve Springs for V-Twin Commands  These spring locators fits our double springs and are centered on the stock Command valve guide.  Keeps spring from eating into the aluminum head and keeping the spring center on the guide.  $16.00 set of four
   

Kohler Command Big Twin (34hp - 40hp) Flywheel.  This is an adjustable steel flywheel designed  for the new 34hp to 40hp Kohler Command V-twin.  We refer to this engine as the Big Block Command.  In stock ready for shipment. Priced at $275.00

We also have aluminum clutch hubs available for this flywheel and also fits stock flywheels. Price is $52.50.

 Lawn Mower Racer Command Aluminum Flywheel with cooling fins  This aluminum flywheel weighs just 10 lbs and has built in cooling fins for your lawn mower racer.  Quick revving out of the corners to get a jump on the competition.  Priced at $350.00 New Steel Billet Stroker Crank for Kohler Command with a 3.120" stroke Made from billet 4340 steel, super finished.  This 3.120" stroke is the largest available anywhere, but it does require some clearancing in the block (we've been running an engine all season with this setup).  Priced at $675.00  We also have rods available for this setup (to use with .750" pin height pistons).  Priced at $140.00 per rod. 
Kohler Command Big Twin (34hp - 40hp) Billet Steel Cam Blank.  
This is a billet steel cam blank for the big block v-twin Kohler Command engines.  Also available (but not pictured) is an adjustable steel camshaft gear.  
Price of Cam Blank is $125.00.  Price of Cam Gear is $75.00 		 Long Rods for Kohler Command.  
These longer rods for are for the 18hp to 30hp V-twin for use with the .750 pin height pistons.  Dyno test show increased top end horsepower of 5 to 10 hp over the short rod engines.  These longer rods improve the rod angularity of the v-twin to increase piston dwell time on TDC and BDC for increased and more efficient cylinder filling resulting in more horsepower.  Priced at $220.00 per pair. 
 .062" Copper Head Gaskets for Command.  
These thicker head gaskets are good to use for gaining a little bit more clearance for valve to piston clearance on bigger camshafts.  Available in three sizes for 18hp -22hp, 25hp and 3.375" bore.  Priced at $26.00 per pair.
Command Big V-Twin 34hp - 40hp Copper Head Gaskets.   
These head gaskets are .031" thick.  Works with the 34hp thru the 40hp models.  Priced at $27.00 per pair.		 Dome Pistons for the 34hp to 40hp Kohler Command V-Twin.  Increase the compression ratio to 12.6:1, fits stock rods or our Billet rods and are the stock bore diameter.  Priced at $172.00 per piston assembly which includes rings, wrist pin and clips.  JE 3540 Billet Aluminum rods for the 34hp to 40hp Kohler Command V-Twin.  Stock length and comes with heavy duty 3/8" rod bolts.  Priced at $140.00 per rod.  Rod bearings available for $36.00 for per set (enough for 2 rods).
Dyna Coil Pack (green) and aluminum bracket that bolts on in place of the factory V-Twin coils.  Bracket is designed to work with 2 barrel or aftermarket intake manifold (will not work with stock 18hp to 27hp intake manifold).  These Dyna coils are the widely used in high performance motorcyles including G2 S&S Pro Stock NHRA Drag Bike. These coils have been tested on our V-twin engines the past two years.  Part Number: "EI -Vtwin Coils". Price $200.00 Crank Trigger Ignition for Kohler Command V-Twin Engines.  Kit includes magnet ring, bracket and modules.  Easy hook up.  Buyer must specify diameter of PTO end of crank at the block. MWSC steel crank requires a 1.5" magnet ring.  Also must specify bolt circle on front of the block for the module bracket to bolt on (5" or 5 5/8").  This crank trigger should be used with two (2) coils (like the Bosch Super Blue Coils) or Dyna Coil packs listed below (recommended).  This ignition set up has been tested on our V-twin engines for the past two years.  Part Number is "EI - VTwin". Priced at $160.00. Kohler Command V-Twin Non-Adjustable Steel Flywheel to be used with our crank trigger ignition.  Flywheel is degreed and included is a timing pointer which bolts onto the block where the stock coils were mounted.  Part Number "FC32"  Priced at $175.00
PURCHASE Both the FC32 flywheel and the EI VTwin for $335.00  Part Number "FC32A".
Purchase The Crank Trigger/Dyna Coil Setup kit.  Kit includes the Crank Trigger Kit and the Dyna Coil Kit for $360.00.
Purchase the entire Complete Package.  Kit includes Flywheel, Crank Trigger and Dyna Coils. Kit is $535.00